Racing Studs - Haucker Plates

Each plate is 3/4" wide and hold two studs at a 15degree angle. The studs are easily replaced. Available separately or as sets. Sets include plates, mounting bolts, short t-nuts and steel picks for .700" overall height.
 CS15P 
 CS15 
   Cleated Track - Plates Only 
 Cleated Track - 12 sets 
   $23.95 
 $49.95 
   Add to Cart 
 Add to Cart 


Combo plates are the best of both worlds - straight line traction and cornering traction in one plate. The CR200 and CL200 are similar to the RT30 and LT30 for rubber tracks and include mounting bolts and 1" t-nuts. The smaller CB150P is designed for cleated tracks, is 3/4" wide and can be purchased as a set (plates, mounting bolts, short barrel t-nuts and steel picks for a .700" mounting height) or plates can be ordered separately.
 CB150P 
 CL200 
 CR200 
 CB150 
   Plates Only 
 Left Turn 
 Right Turn 
 12 sets 
   $23.95 
 $27.95 
 $27.95 
 $49.95 
   Add to Cart 
 Add to Cart 
 Add to Cart 
 Add to Cart 


The only corner plate designed for rubber tracks. Allows you to really slice through the corners - does not affect holeshots. Holds three replaceable studs at a 15 degree angle. This plate has the same bolt pattern as a two hole bender-style plate or Accord's ABP245. The plate is 1 1/2" wide x 1/4" thick available in left and right hand models. Comes with mounting bolts and 1" t-nuts. Order studs separately.

 LT30 
 RT30 
   Corner Plates - Left Hand 
 Corner Plates - Right Hand 
   $27.95 
 $27.95 
   Add to Cart 
 Add to Cart 

This is the plate that propelled Pat Hauck to numerous wins on his Yamaha V-Max 4. A 3/4" wide x 2" long tempered aluminum plate which mounts two studs on a 22 degree angle. The plate works on reversed or standard rubber tracks. They will maximize your holeshot without pushing you through the corners. You can buy just the plate or in sets. Each set includes the plate, mounting bolt, a 1" t-nut and two Accord 1" long steel picks.

 HS22P 
 HS22 
   Haucker Holeshot - Plates Only 
 Haucker Holeshot Kit - 12 sets 
   $23.95 
 $49.95 
   Add to Cart 
 Add to Cart 

This plate is similar to the HS22 plate but is designed for tracks mounted in the stock rotating direction (called standard tracks). This plate is beveled to fit tight against the rib of the track for added support to prevent flexing. It has a 15 degree stud angle and is 1 1/2" wide x 1/4" thick. Ideal for quick changing from trail studs to a full race setup. Uses the same mounting bolt pattern as a bender-style plate such as the Accord Macro ABP series. For your trail setup use trail carbide studs such as a Razorback with an ABP145 backer. Unscrew the stud and remove with the backer. Using the same t-nut and hole location - bolt on the RT20 Haucker plate and go racing. Purchase plates separately or as a set. Sets include one plate, 1" t-nuts, mounting bolt and two 1" steel picks.

 RT20P 
 RT20 
   Holeshot Kit - Plates Only 
 Holeshot Kit - Haucker Plates 
   $23.95 
 $49.95 
   Add to Cart 
 Add to Cart 

3 Hole Razor Plates

 HP3 
   3 Hole Razor Plate - 48pcs 
   $99.95 
   Add to Cart 

Plates for Cleated Tracks
Plates for holeshots for cleated tracks with studs mounted at an angled for under the slide rail positioning. Twin trackers use TT1050 with a 15 degree attack angle. For single track sled with a 2 3/4" bolt pattern use the TT5050 with a 22 degree attack angle. These are great for launching heavy and open mod sled with a minimum of studding. Packs include 12 plates and 24 mounting bolts. The most popular length stud to use in a 3/4" steel razor, which must be ordered separately. Ideal for Wahl cleats.

 TT5050 
 TT1025P 
 TT1050 
   Single Track - Haucker Kit 
 Wahl Track - Plates Only 
 Twin Tracker - Kit - Plates Only 
   $35.95 
 $23.95 
 $35.95 
   Add to Cart 
 Add to Cart 
 Add to Cart 

Starter Stud Plates
Starter stud plates are the trick for getting the holeshot. They are made to mount under the slide rails on cleated tracks. An aircraft aluminum host bar is secured to the track using 1/4-20 flat head screws (included). Two Accord steel razors are screwed into the host bar for an overall height of .700" Starter stud plates for twin or single tracks. Reverse mounting will give you four lines of traction. The replaceable studs are too sharp to handle - Wear Protection.

 TT1000P 
 TT1000 
 TT2500 
 TT5000P 
 TT5000 
   Cleated Track - Haucker Kit - Plates Only 
 Cleated Track - Haucker Kit 
 In Between Haucker Kit 
 Single Track Haucker Kit - Plates Only 
 Single Track Haucker Kit 
   $23.95 
 $49.95 
 $49.95 
 $23.95 
 $49.95 
   Add to Cart 
 Add to Cart 
 Add to Cart 
 Add to Cart 
 Add to Cart